Flat Top Griddles, Maintenance & Safety, Tips & Techniques

Flat Top Grill First Use: Everything You Need to Do

Before cooking on a new flat top grill, clean off manufacturing residue, season the surface with 3-5 coats of oil, and do a break-in cook. This takes about 2 hours but only needs to be done once. After that, a quick post-cook oil coat after each use maintains the surface.

What to Do Before Turning It On

Unbox and assemble the Daytona fully before doing anything else. Once assembled, do a quick pre-use check:

  • Check that all burner knobs turn smoothly and click into the START/HIGH, MEDIUM, and LOW positions.
  • Check the igniter fires on each burner – press the button and listen for a click and spark.
  • Check the propane connection is tight – no loose fittings between the regulator and tank.
  • Check the grease trap is in place and the drain is unobstructed.

Do not skip the propane connection check. A loose fitting means gas escapes at the connection instead of flowing to the burners.

Step 1: Initial Clean

Wiping down a new flat top grill surface with a cloth

New griddles come with residue from the manufacturing process – metal dust, protective coatings, and packaging debris. Remove all of this before the first season.

  1. Mix warm water with a small amount of dish soap.
  2. Wipe down the entire griddle cooking surface with a cloth or paper towels dampened with the soapy water.
  3. Rinse with clean water and wipe dry.
  4. Let the surface air-dry for at least 15 minutes before moving to the seasoning step.

This is the only time you use soap on the cooking surface. After this, cleaning is done with a scraper and water only – soap strips the seasoning layer.

Step 2: Season the Surface

Applying oil to a flat top grill surface during first seasoning

Seasoning creates the protective, non-stick coating that makes a flat-top griddle perform well. For a new Daytona with the NitroGuard™ surface, 3 coats are sufficient. For a bare steel surface, do 5 coats.

What you need

Seasoning process - repeat 3 times (NitroGuard™) or 5 times (bare steel)

Steam rising from a hot Nexgrill Daytona flat top grill surface
  1. Turn all burners to HIGH. Preheat for 10-15 minutes until the surface begins to discolor. This is normal.
  2. Apply a very thin layer of oil to the entire cooking surface using a folded paper towel held with tongs. Include the edges. The oil layer should be almost invisible – not pooling.
  3. Leave the burners on HIGH. The oil will begin to smoke as it polymerizes. Wait until the smoke completely stops – 10-15 minutes.
  4. The surface will have darkened. This is the seasoning layer forming.
  5. Repeat from step 1. Apply the next coat of oil and burn it off.

After the final coat, turn off the burners and let the griddle cool completely before touching the surface. The finished surface should look dark, feel smooth, and be completely dry to the touch - not sticky.

Step 3: The Break-In Cook

Bacon cooking on a Nexgrill Daytona flat top griddle

The break-in cook is the first actual cook on the seasoned surface. It further builds the seasoning layer and tests the griddle before you cook anything you care about.

Choose something simple and fatty – bacon is ideal. The rendered fat adds to the seasoning layer and is forgiving if the surface isn't perfectly even yet.

  1. Preheat the Daytona to medium-high (375-400°F) for 8-10 minutes.
  2. Add a thin layer of canola or vegetable oil to the surface.
  3. Lay bacon strips across the surface. Cook for 3-4 minutes per side.
  4. Remove the bacon. While the surface is still hot, scrape any residue toward the grease trap.
  5. Add a splash of water to steam off any remaining bits. Wipe with a paper towel.
  6. Apply a thin layer of oil to the warm surface. Allow to cool.

The griddle is now ready for regular use. The surface will continue to improve with each subsequent cook.

After Every Cook: The Maintenance Routine

This routine takes under 2 minutes and keeps the griddle in perfect condition.

  1. While the surface is still hot, scrape clean with the griddle scraper. Push debris toward the grease trap.
  2. Add 2-3 tablespoons of water to loosen any stuck residue. The steam lifts it off.
  3. Wipe down with a paper towel.
  4. Apply a very thin layer of high smoke-point oil to the surface while it's still warm.
  5. Allow to cool completely before fitting the cover.

The cover goes on after the surface has cooled – not while it's still hot. Trapping heat under a cover can cause condensation on the surface and lead to rust.

What to Cook First

After the break-in cook, start with something forgiving that lets you get familiar with the heat zones.

  • Smash burgers – teaches the sear technique and how to manage the hot zone. Hard to get wrong.
  • Bacon and eggs – teaches multi-zone cooking using different burner settings simultaneously. Good second cook.
  • Pancakes – teaches temperature sensitivity and patience. Good for understanding how the surface retains heat.

Avoid delicate fish and anything that requires very precise temperature control on the first few cooks – those are better once you understand how your specific griddle behaves.

Common First-Use Mistakes

  • Not cleaning before the first season – manufacturing residue affects flavor and the first cook.
  • Applying too much oil during seasoning – creates a sticky, gummy surface. The oil coat should be almost invisible.
  • Not doing enough seasoning coats – one coat is not enough. At least three coats for NitroGuard, five for bare steel.
  • Cooking immediately after the last seasoning coat – allow the surface to cool completely first.
  • Skipping the post-cook oil coat – this is what maintains the seasoning layer between cooks. Skipping it shortens the surface's lifespan.
  • Fitting the cover while the surface is still hot – condensation under a hot cover causes rust.

Related Guides

Frequently Asked Questions

What do you do with a flat top grill for the first time?

Clean the surface with warm soapy water to remove manufacturing residue, dry completely, then season with 3-5 thin coats of high smoke-point oil – applying each coat on a preheated surface at high heat and allowing it to burn off before the next. After seasoning, do a break-in cook with bacon before your first real meal.

Do you have to season a flat top grill before first use?

Yes. An unseasoned flat top griddle has bare metal exposed to food – it will rust quickly, food will stick, and there may be a metallic taste from the uncoated surface. The initial seasoning session takes about 2 hours and only needs to be done once. The Nexgrill Daytona with NitroGuard requires 3 coats; bare steel surfaces require 5.

What should I cook first on a flat top grill?

Bacon is the ideal break-in cook - the rendered fat adds to the seasoning layer, and the technique is forgiving. For the first actual meal, smash burgers or bacon and eggs are the best choices. Both teach the core flat top techniques (searing, multi-zone heat management) and are hard to get wrong.

How long does it take to season a new flat top grill?

Approximately 1.5-2 hours for the initial seasoning. Each coat takes 10-15 minutes to apply and burn off, plus cooling time between coats. 3 coats for a NitroGuard surface (Daytona), 5 coats for bare steel. Allow the griddle to cool completely after the final coat before cooking.

Can you use a flat top grill right out of the box?

No. You need to clean off manufacturing residue and season the surface before the first cook. Cooking on an unseasoned flat top means food contacts manufacturing residue, the surface will rust quickly, and food will stick. The initial seasoning takes about 2 hours and is a one-time process.