Charcoal Grills & Smokers, Maintenance & Safety, Tips & Techniques

How to Season a Smoker Before First Use

Season a new smoker by coating the interior with a thin layer of high smoke-point oil and running it at high heat (250-300°F) for 2-3 hours. This burns off manufacturing residue, creates a non-stick coating, and improves smoke flavor. Do this before your first cook – skipping it affects both safety and food taste.

Why You Need to Season a Smoker

New smokers come with residue from the manufacturing process – paint, solvents, protective coatings, and metal dust. Seasoning burns it off before it contacts your food.

It also creates a layer of polymerized oil on the interior surfaces. This layer:

  • Prevents rust on bare metal surfaces
  • Creates a non-stick cooking surface over time
  • Contributes to better smoke flavor in subsequent cooks
  • Extends the life of the smoker

What You Need

  • High smoke-point cooking oil (see oil guide below)
  • Paper towels or a clean cloth
  • Charcoal or wood (enough for a 2-3 hour burn)
  • Lighter and fire starters
  • A few hours – do not rush this process

Best Oil to Season a Smoker

Use a thin coat – not a thick layer. Too much oil creates a sticky, gummy surface instead of a hard, protective coating.

Oil Smoke point Best for Notes
Flaxseed oil 225°F First seasoning Best polymerization – ideal for initial seasoning
Vegetable oil 400°F Ongoing use Good general-purpose option
Canola oil 400°F Ongoing use Neutral flavor, widely available
Crisco / shortening 360°F First seasoning Popular alternative to flaxseed

How to Season a Smoker (Step by Step)

Step 1: Clean the smoker

  1. Wipe down all interior surfaces with a damp cloth to remove dust and debris from packaging.
  2. Do not use soap – it leaves residue that affects flavor.
  3. Allow to dry completely before applying oil.

Step 2: Apply oil to all interior surfaces

  1. Use a paper towel or cloth to apply a thin, even coat of oil to the cooking grates, the interior walls of the cooking chamber, the inside of the firebox lid, and the water pan (if your smoker has one).
  2. Wipe off any excess – you want a thin film, not pooling oil.
  3. Do not oil the outside of the smoker.

Step 3: Light the smoker and run it at high heat

Smoke rising from a Nexgrill Oakford offset smoker during a seasoning burn
  1. Load the firebox with charcoal or wood and light it.
  2. Open all vents fully to allow maximum airflow.
  3. Bring the smoker up to 250-300°F.
  4. Hold this temperature for 2-3 hours. Add fuel as needed to maintain heat.
  5. During this time, the oil will polymerize – you'll see it harden and darken on the surfaces. You may see light smoke coming from the cooking chamber. This is normal.

Step 4: Allow to cool completely

  1. After 2-3 hours, close the vents to restrict airflow and allow the fire to die down naturally.
  2. Do not open the smoker while it is cooling – leave it closed to retain heat and continue the seasoning process.
  3. Allow to cool completely before opening. The interior surfaces should look darkened and have a dry, non-tacky finish.

Step 5: Inspect and repeat if needed

Interior of a Nexgrill Oakford Outpost 29 offset smoker
  1. Check all surfaces. The coating should be dark, dry, and smooth – not sticky or uneven.
  2. If you see sticky or gummy patches, you applied too much oil. Run the smoker at high heat for another hour to cure the excess.
  3. Some smokers benefit from 2-3 seasoning sessions before the first cook. The Oakford Outpost 29 offset smoker develops its best cooking surface after 2 full sessions.

How Often to Re-Season a Smoker

Re-season the smoker when:

  • Rust spots appear on interior surfaces
  • The cooking surface becomes sticky or uneven
  • The smoker has been stored for an extended period
  • You've done a deep clean with soap and water

Regular use naturally builds up the seasoning layer. A smoker that is used frequently rarely needs re-seasoning between cooks.

Seasoning a Pellet Grill vs. an Offset Smoker

Clean cooking grates of the Nexgrill Oakford 36A pellet grill

The process differs slightly depending on the smoker type.

  • Offset smoker (Oakford Outpost 29) – season using charcoal and wood. Apply oil to the cooking chamber and firebox interior. Run at 250-300°F for 2-3 hours.
  • Pellet grill (Oakford 36A) – apply oil to the cooking grates and interior. Run a burn-in cycle at the manufacturer's recommended temperature (typically 350°F for 45 minutes). The Oakford 36A includes a first-use burn-in guide – follow that process before the first cook.

Related Guides

Frequently Asked Questions

Do you need to season a new smoker?

Yes. New smokers contain manufacturing residue – paint, solvents, and metal dust – that must be burned off before the smoker contacts food. Seasoning also creates the protective coating that prevents rust and improves cooking performance.

How long does it take to season a smoker?

2-3 hours at 250-300°F. Allow additional time for the smoker to cool completely before inspecting. The full process takes 4-5 hours from start to finish. Some smokers benefit from a second session before the first cook.

What oil do you use to season a smoker?

Flaxseed oil is the best choice for the initial seasoning – it polymerizes well at high heat, creating a hard, durable coating. Vegetable oil and canola oil are good alternatives for ongoing maintenance seasoning. Apply a thin layer - too much oil creates a sticky surface rather than a protective coating.

Can you cook on a smoker before seasoning it?

No. Cooking on an unseasoned smoker means food contacts manufacturing residue, including paint, solvents, and metal dust. Always season before the first cook.

How do you know when a smoker is fully seasoned?

The interior surfaces should be darkened, dry, and smooth – not sticky or tacky. If surfaces feel gummy, the oil coat was too thick. Run the smoker at high heat for another hour to cure the excess oil.